FURNACE REFERENCE · Manufacturer-sourced; not reviewed by a qualified technician
HVACFaultFinder

Lennox furnace code reference

Identify the full manual and source context before comparing an already observed pattern.

LENNOX / FURNACE / MANUAL-SCOPED PILOT

506763-01 · SL280UHV

Selected integrated-control diagnostic/status entries for the SL280UHV two-stage furnace. The 06/2011 manual covers communicating and noncommunicating applications; it does not establish a match for every Lennox furnace, thermostat or replacement control. Check available paperwork. Do not open equipment to identify a control.

Open 506763-01 · source cover → June 2011 edition, supersedes March 2011; exact publication day unconfirmed. Owner-supplied PDF, visually inspected. Direct byte comparison with the manufacturer-hosted download was unavailable.

Thirty-nine selected furnace/control/electrical entries from Integrated Control Diagnostic Codes, printed / PDF pages 61–64. Source layout E 110 is displayed as E110. Preserve the E prefix; digits alone and LED flash counts are not equivalent.

This is a partial table selection. Normal states, communication-only rows and outdoor-unit alerts are excluded. E117 is a warning only. E229 describes ignition on high fire; the source says no action is needed. Neither establishes a failed part. Recovery and repair directions are excluded.

  1. Code E110

    Low line voltage.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 61 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  2. Code E111

    Line voltage polarity reversed.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 61 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  3. Code E112

    Ground not detected.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 61 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  4. Code E113

    High line voltage.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 61 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  5. Code E114

    Line voltage frequency out-of-range.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 61 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  6. Code E115

    Low 24V.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 61 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  7. Code E116

    High 24V.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 61 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  8. Code E117

    Poor ground detected (Warning only).

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count. The manufacturer labels this a warning only.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 61 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  9. Code E200

    Hard lockout — rollout circuit open or previously open.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 62 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  10. Code E201

    Indoor blower communication failure — unable to communicate with blower motor.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 62 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  11. Code E202

    Indoor blower motor mismatch — indoor motor horsepower does not match unit capacity.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 62 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  12. Code E203

    Appliance capacity / size is not programmed; invalid unit codes.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 62 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  13. Code E204

    Gas valve miswired.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 62 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  14. Code E205

    Gas valve control relay contact shorted.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 62 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  15. Code E206

    Gas valve second-stage relay failure.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 62 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  16. Code E207

    Hot surface ignitor sensed open.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 62 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  17. Code E223

    Low pressure switch failed open.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  18. Code E224

    Low pressure switch failed closed.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  19. Code E225

    High pressure switch failed open.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  20. Code E226

    High pressure switch failed closed.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  21. Code E227

    Low pressure switch open during trial for ignition or run mode.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  22. Code E228

    Combustion air inducer calibration failure.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  23. Code E229

    Ignition on high fire.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count. Operating condition: ignition on high fire; the source says no action is needed. It does not by itself establish a failed part.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  24. Code E240

    Low flame current — run mode.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  25. Code E241

    Flame sensed out of sequence — flame still present.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  26. Code E250

    Limit switch circuit open.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  27. Code E252

    Discharge air temperature too high (gas heat only).

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  28. Code E270

    Soft lockout — exceeded maximum retries; no flame current sensed.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  29. Code E271

    Soft lockout — exceeded maximum retries; last retry failed due to the pressure switch opening.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 63 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  30. Code E272

    Soft lockout — exceeded maximum recycles; last recycle due to the pressure switch opening.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 64 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  31. Code E273

    Soft lockout — exceeded maximum recycles; last recycle due to flame failure.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 64 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  32. Code E274

    Soft lockout — exceeded maximum recycles; last recycle failed due to the limit circuit opening or remaining open longer than 3 minutes.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 64 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  33. Code E275

    Soft lockout — flame sensed out of sequence; flame signal is gone.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 64 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  34. Code E276

    Watchguard calibration failure.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 64 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  35. Code E290

    Ignitor circuit fault — failed ignitor or triggering circuitry.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 64 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  36. Code E291

    Heat air flow restricted below the minimum.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 64 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  37. Code E292

    Indoor blower motor unable to start due to obstructed wheel or seized bearings.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 64 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  38. Code E294

    Combustion air inducer over current.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 64 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

  39. Code E295

    Indoor blower motor temperature is too high.

    SL280UHV two-stage furnace integrated-control table only. Communicating and noncommunicating applications exist; no installed control or thermostat match is confirmed. E prefix is required; this is not a flash count.

    Manufacturer table heading only, not a confirmed cause or repair instruction. selected integrated-control diagnostic/status table context only; exact unit/control applicability remains unconfirmed.

    Manufacturer-sourced; not reviewed by a qualified technician.

    506763-01 · printed / PDF page 64 · Integrated Control Diagnostic Codes · manufacturer download lead

    Return to Lennox lookup → · Record observations for service →

If the furnace is not heating, documentation is uncertain or a pattern is unlisted, contact a qualified HVAC professional. Do not open panels, change switches, bypass safeties, reset equipment or test gas/electrical parts using this reference. If you suspect gas leakage or a carbon monoxide hazard, leave the area and contact emergency services or your utility from a safe location.

Prepare observations without a code →