FURNACE REFERENCE · Manufacturer-sourced; not reviewed by a qualified technician
HVACFaultFinder

Goodman furnace code and pattern reference

This reference covers selected rows from three manufacturer manuals, not every Goodman furnace. Literal cover families and source pages remain with each entry; a partial model name cannot establish an installed control match.

GOODMAN / FURNACE / HOMEOWNER PILOT

Find the source explanation. Keep the equipment context.

Use the full manual identifier from your equipment documents, then the pattern you can already see. A flashing light or a partial model name cannot choose the right manual for you.

Not heating and no code? Start with the observation guide → No code is required.

How do I identify the manual?
  1. Use paperwork you already have. Look for the document identifier on its cover or footer and compare the full identifier, including the final letter.
  2. Compare the cover date and literal family notation. Similar model names or a newer date do not establish the same control or manual.
  3. If you cannot identify it, leave the selection at Not sure. Do not guess from the flash count or open equipment to find a label.

These references are separate sources, not a list of confirmed equipment matches:

  • IOG-2009P · cover 09/2019 · *MSS9* / *CSS9* · Single-stage gas furnace
  • IOG-2011R · cover 04/20 · *MEC96 / *CEC96 · Two-stage gas furnace · separate green, amber and red indicators
  • IOG-2015F · cover 10/2020 · *CVC96*BB / *MVC96*BB · Two-stage gas furnace · alphanumeric LED display

Wildcards remain literal. Exact model suffixes and installed control versions have not been matched.

Observe only what is already accessible. Do not remove panels, touch wiring or operate service controls to find a code or model label. Ask a qualified service provider to establish applicability when documentation is uncertain.

What to record, and when to seek help

  • Keep the full model designation, manual identifier and observed pattern together. Record whether it repeats or appears only at startup.
  • A source description is not proof of the cause. This pilot supplies no equipment repair checks or reset instructions.
  • If the furnace is not operating, documentation is uncertain or the pattern is not covered, contact a qualified HVAC professional. Do not substitute a similar code from another manual.

If you suspect gas leakage or a carbon monoxide hazard, leave the area and contact emergency services or your utility from a safe location.

Safety boundaries · How documented sources are used · Compare original Goodman manual references

MANUFACTURER DOCUMENTATION / PREVIEW

Start with the manual, then the model

Similar flash counts can mean different things on different furnace controls. Keep the manual, model family and indicator type together.

Manufacturer-sourced · Not independently verified

IOG-2009P

*MSS9* / *CSS9*

Single-stage gas furnace

Document title
Installation Instructions for *MSS9* & *CSS9* Single-Stage Gas Furnace
Cover date
09/2019 (month/year only)
Reference location
Printed / PDF page 39 · Diagnostic Codes
Accessed
2026-11-13
Applicability
Cover family notation only. Wildcards are literal; exact unit and control applicability remain unconfirmed.
Official Goodman document · IOG-2009P (PDF viewer)

IOG-2009P source table · Source reference preview

Manufacturer-sourced; not independently verified. Not reviewed by a qualified technician. These are transcriptions, not diagnoses. Cover families: *MSS9* / *CSS9*. Exact equipment and control applicability remain unconfirmed.

Operating context mattersThe manual also says the LED flashes once at power-up. Do not equate a startup flash with a repeating fault pattern. ON is listed as normal operation, not a fault. Do not transfer these meanings to another manual or control.

  1. 1 flash, then pause
    What the manufacturer documents

    System lockout

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Page 39 diagnostic indicator table; LED also flashes once at power-up. Exact installed operating context is unconfirmed.

    Control applicability: Cover families *MSS9* / *CSS9* only. Exact control-board identifier, suffix and current unit applicability are unconfirmed.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2009P · Cover 09/2019 · Printed page 39 / PDF page 39 · DIAGNOSTIC CODES

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  2. 2 flashes, then pause
    What the manufacturer documents

    Pressure switch stuck closed

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Page 39 diagnostic indicator table; LED also flashes once at power-up. Exact installed operating context is unconfirmed.

    Control applicability: Cover families *MSS9* / *CSS9* only. Exact control-board identifier, suffix and current unit applicability are unconfirmed.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2009P · Cover 09/2019 · Printed page 39 / PDF page 39 · DIAGNOSTIC CODES

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  3. 3 flashes, then pause
    What the manufacturer documents

    Pressure switch stuck open

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Page 39 diagnostic indicator table; LED also flashes once at power-up. Exact installed operating context is unconfirmed.

    Control applicability: Cover families *MSS9* / *CSS9* only. Exact control-board identifier, suffix and current unit applicability are unconfirmed.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2009P · Cover 09/2019 · Printed page 39 / PDF page 39 · DIAGNOSTIC CODES

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  4. 4 flashes, then pause
    What the manufacturer documents

    Open limit switch

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Page 39 diagnostic indicator table; LED also flashes once at power-up. Exact installed operating context is unconfirmed.

    Control applicability: Cover families *MSS9* / *CSS9* only. Exact control-board identifier, suffix and current unit applicability are unconfirmed.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2009P · Cover 09/2019 · Printed page 39 / PDF page 39 · DIAGNOSTIC CODES

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  5. 5 flashes, then pause
    What the manufacturer documents

    Flame has been sensed when no flame should be present (no call for heat)

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Page 39 diagnostic indicator table; LED also flashes once at power-up. Exact installed operating context is unconfirmed.

    Control applicability: Cover families *MSS9* / *CSS9* only. Exact control-board identifier, suffix and current unit applicability are unconfirmed.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2009P · Cover 09/2019 · Printed page 39 / PDF page 39 · DIAGNOSTIC CODES

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  6. 6 flashes, then pause
    What the manufacturer documents

    Open rollout switch / open control board fuse

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Page 39 diagnostic indicator table; LED also flashes once at power-up. Exact installed operating context is unconfirmed.

    Control applicability: Cover families *MSS9* / *CSS9* only. Exact control-board identifier, suffix and current unit applicability are unconfirmed.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2009P · Cover 09/2019 · Printed page 39 / PDF page 39 · DIAGNOSTIC CODES

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  7. 7 flashes, then pause
    What the manufacturer documents

    Low flame sense signal

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Page 39 diagnostic indicator table; LED also flashes once at power-up. Exact installed operating context is unconfirmed.

    Control applicability: Cover families *MSS9* / *CSS9* only. Exact control-board identifier, suffix and current unit applicability are unconfirmed.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2009P · Cover 09/2019 · Printed page 39 / PDF page 39 · DIAGNOSTIC CODES

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  8. 8 flashes, then pause
    What the manufacturer documents

    Igniter relay fault

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Page 39 diagnostic indicator table; LED also flashes once at power-up. Exact installed operating context is unconfirmed.

    Control applicability: Cover families *MSS9* / *CSS9* only. Exact control-board identifier, suffix and current unit applicability are unconfirmed.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2009P · Cover 09/2019 · Printed page 39 / PDF page 39 · DIAGNOSTIC CODES

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  9. Continuous flashing
    What the manufacturer documents

    115 Volt AC power reversed

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Page 39 diagnostic indicator table; LED also flashes once at power-up. Exact installed operating context is unconfirmed.

    Control applicability: Cover families *MSS9* / *CSS9* only. Exact control-board identifier, suffix and current unit applicability are unconfirmed.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2009P · Cover 09/2019 · Printed page 39 / PDF page 39 · DIAGNOSTIC CODES

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  10. OFF
    What the manufacturer documents

    Control failure

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Page 39 diagnostic indicator table; LED also flashes once at power-up. Exact installed operating context is unconfirmed.

    Control applicability: Cover families *MSS9* / *CSS9* only. Exact control-board identifier, suffix and current unit applicability are unconfirmed.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2009P · Cover 09/2019 · Printed page 39 / PDF page 39 · DIAGNOSTIC CODES

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  11. ON
    What the manufacturer documents

    Normal operation

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Page 39 diagnostic indicator table; LED also flashes once at power-up. Exact installed operating context is unconfirmed.

    Control applicability: Cover families *MSS9* / *CSS9* only. Exact control-board identifier, suffix and current unit applicability are unconfirmed.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2009P · Cover 09/2019 · Printed page 39 / PDF page 39 · DIAGNOSTIC CODES

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

No homeowner checks or professional procedures are supplied. Guidance has not been assessed; this does not mean no service or escalation is needed. This preview is not authorization to diagnose or repair equipment.

Manufacturer-sourced · Not independently verified

IOG-2011R

*MEC96 / *CEC96

Two-stage gas furnace · separate green, amber and red indicators

Document title
*MEC96 & *CEC96 Two-Stage Gas Furnaces (Type FSP CATEGORY IV Direct or Non Direct Vent Air Furnace)
Cover date
04/20 (month/year only)
Reference location
Printed / PDF pages 57–58 · Troubleshooting Chart; page 53 · Limit Fault Codes
Accessed
2026-11-13
Applicability
Cover family notation only. Wildcards are literal; exact unit and control applicability remain unconfirmed.
Official Goodman document · IOG-2011R (PDF viewer)

IOG-2011R source table · Source reference preview

Manufacturer-sourced; not independently verified. Not reviewed by a qualified technician. These are transcriptions, not diagnoses. Cover families: *MEC96 / *CEC96. Exact equipment and control applicability remain unconfirmed.

Operating context mattersGreen, amber and red indicators have separate meanings. Double flashes are not single repeating flashes. Normal states and faults appear together in this chart. Page 53 adds time-dependent conditions to limit faults. Do not transfer these meanings to another manual or control.

  1. Green: None; Amber: None; Red: None
    What the manufacturer documents

    Defective disconnect switch; defective door switch; No 115 volt power; No 24 volt power

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate; control board LED is off.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  2. Green: Solid ON; Amber: None; Red: None
    What the manufacturer documents

    Furnace is not receiving a call

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace is waiting for a call.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  3. Green: Rapid Flash; Amber: None; Red: None
    What the manufacturer documents

    Furnace is receiving a call for fan (24 volts on G terminal

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fan only is running.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  4. Green: One repeating flash; Amber: None; Red: None
    What the manufacturer documents

    Normal operation with low stage call for cooling (Ylo & G)

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Normal operation with low stage call for cooling (Ylo & G).

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  5. Green: Two repeating flashes; Amber: None; Red: None
    What the manufacturer documents

    Normal operation with high or single stage call for cooling (Y & G)

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Normal operation with high or single stage call for cooling (Y & G).

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  6. Green: None; Amber: One repeating flash; Red: None
    What the manufacturer documents

    Normal operation with low stage call for heat (W1)

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Normal operation with low stage call for heat (W1).

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  7. Green: None; Amber: Two repeating flashes; Red: None
    What the manufacturer documents

    Normal operation with high or single stage call for heat

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Normal operation with high or single stage call for heat.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  8. Green: None; Amber: Three repeating flashes; Red: None
    What the manufacturer documents

    W2 call present without W1

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, three Amber flashes on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  9. Green: None; Amber: Four repeating flashes; Red: None
    What the manufacturer documents

    Ylo or Y call present without G

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, four Amber flashes on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  10. Green: None; Amber: Rapid; Red: None
    What the manufacturer documents

    Low flame sense current

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, rapid Amber flashes on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  11. Green: None; Amber: None; Red: One repeating flash
    What the manufacturer documents

    Flame sensed when no flame should be present

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, one Red flash on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  12. Green: None; Amber: None; Red: Two repeating flashes
    What the manufacturer documents

    Pressure switch stuck closed

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, two Red flashes on control board, possible inducer operation.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  13. Green: None; Amber: None; Red: Three repeating flashes
    What the manufacturer documents

    Low fire pressure switch stuck open

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, three Red flashes on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 57 / PDF page 57 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  14. Green: None; Amber: None; Red: Four repeating flashes
    What the manufacturer documents

    Open limit circuit, main limit, aux limit, or roll out switch

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, four Red flashes on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 58 / PDF page 58 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  15. Green: None; Amber: None; Red: Five repeating flashes
    What the manufacturer documents

    Limit & rollout circuit open for 15 minutes. Open control board fuse or rollout switch

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, five Red flashes on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 58 / PDF page 58 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  16. Green: None; Amber: None; Red: Six repeating flashes
    What the manufacturer documents

    Pressure switch cycling lockout, pressure switch has opened 5 times in the same heating cycle

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, six Red flashes on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 58 / PDF page 58 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  17. Green: None; Amber: None; Red: Seven repeating flashes
    What the manufacturer documents

    Lockout - excessive retries from flame not being proven during trial for ignition

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, seven Red flashes on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 58 / PDF page 58 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  18. Green: None; Amber: None; Red: Eight repeating flashes
    What the manufacturer documents

    Lockout - excessive recycles from flame proving being lost after being proven

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, eight Red flashes on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 58 / PDF page 58 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  19. Green: None; Amber: None; Red: Nine repeating flashes
    What the manufacturer documents

    Improper grounding or reverse polarity

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, nine Red flashes on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 58 / PDF page 58 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  20. Green: None; Amber: None; Red: Ten repeating flashes
    What the manufacturer documents

    Gas valve current detected with no call for heat

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, ten Red flashes on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 58 / PDF page 58 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  21. Green: None; Amber: None; Red: Eleven repeating flashes
    What the manufacturer documents

    Open limit switch circuit for more than 5 minutes

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, eleven Red flashes on control board, inducer running.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 58 / PDF page 58 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  22. Green: None; Amber: None; Red: Twelve repeating flashes
    What the manufacturer documents

    Control board igniter relay not energizing igniter

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, twelve Red flashes on control board.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 58 / PDF page 58 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  23. Green: None; Amber: None; Red: Solid ON
    What the manufacturer documents

    Control board internal fault

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, control board Red LED on solid.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 58 / PDF page 58 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  24. Green: None; Amber: None; Red: Rapid Flash
    What the manufacturer documents

    Twinning error

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, control board Red LED rapid flash.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 58 / PDF page 58 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  25. Green: None; Amber: None; Red: Three double flashes
    What the manufacturer documents

    Second stage pressure switch stuck open

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace does not operate, control board Red LED with three double flashes.

    Control applicability: Cover families *MEC96 / *CEC96 only. Separate green, amber and red columns in this source; no exact installed control identifier or suffix is established.

    Flash period: not specified in this extraction. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2011R · Cover 04/20 · Printed page 58 / PDF page 58 · Troubleshooting Chart

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

No homeowner checks or professional procedures are supplied. Guidance has not been assessed; this does not mean no service or escalation is needed. This preview is not authorization to diagnose or repair equipment.

Manufacturer-sourced · Not independently verified

IOG-2015F

*CVC96*BB / *MVC96*BB

Two-stage gas furnace · alphanumeric LED display

Document title
Installation Instructions for *CVC96*BB & *MVC96*BB Two-Stage Gas Furnace
Cover date
10/2020 (month/year only)
Reference location
Printed / PDF pages 46–50 · Troubleshooting Chart (partial extraction)
Accessed
2026-11-13
Applicability
Cover family notation only. Wildcards are literal; exact unit and control applicability remain unconfirmed.
Official Goodman document · IOG-2015F (PDF viewer)

IOG-2015F source table · Source reference preview

Manufacturer-sourced; not independently verified. Not reviewed by a qualified technician. These are transcriptions, not diagnoses. Cover families: *CVC96*BB / *MVC96*BB. Exact equipment and control applicability remain unconfirmed.

Operating context mattersThis is a partial transcription of thirty display-code rows on pages 46–50. Other chart/status rows are not included. Ed0 descriptions and an ambiguous grounding-row token are withheld for source clarification. Display codes must not be treated as flash counts. Do not transfer these meanings to another manual or control.

  1. EE0
    What the manufacturer documents

    Furnace lockout due to an excessive number of ignition “retries” (3 total); Failure to establish flame; Loss of flame after establishment

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 49 / PDF page 49 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  2. EE1
    What the manufacturer documents

    Low stage pressure switch circuit is closed at start of heating cycle; Low stage pressure switch contacts sticking; Short in pressure switch circuit wiring

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 49 / PDF page 49 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  3. EE2
    What the manufacturer documents

    Low stage pressure switch circuit is not closed; Pressure switch hose blocked pinched, or connected improperly; Blocked flue and/or inlet air pipe, blocked drain system or weak induced draft blower; Incorrect pressure switch set point or malfunctioning switch contacts; Loose or improperly connected wiring

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Induced draft blower runs continuously with no furnace operation

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 49 / PDF page 49 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  4. EE3
    What the manufacturer documents

    Primary limit circuit is open; Insufficient conditioned air over the heat exchanger; Blocked filters, restrictive ductwork, improper circulator blower speed, or failed circulator blower motor; Loose or improperly connected wiring in high limit circuit

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Circulator blower runs continuously; No furnace operation

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 49 / PDF page 49 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  5. EE4
    What the manufacturer documents

    Flame sensed with no call for heat; Short to ground in flame sense circuit; Lingering burner flame Slow closing gas valve

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Induced draft blower and circulator blower runs continuously; No furnace operation

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 49 / PDF page 49 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  6. EE5
    What the manufacturer documents

    Open fuse; Short in low voltage wiring

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: No furnace operation

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 49 / PDF page 49 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  7. EE6
    What the manufacturer documents

    Flame sense micro amp signal is low; Flame sensor is coated/oxidized; Flame sensor incorrectly positioned in burner flame; Lazy burner flame due to improper gas pressure or combustion air

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Normal furnace operation

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 49 / PDF page 49 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  8. EE7
    What the manufacturer documents

    Problem with igniter circuit; Improperly connected or shorted igniter; Poor unit ground; Igniter relay fault on integrated control module

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 50 / PDF page 50 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  9. EE8
    What the manufacturer documents

    High stage pressure switch circuit is closed at start of heating cycle. High stage pressure switch contacts sticking; Shorts in pressure switch circuit wiring

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate on high stage; furnace operates normally on low stage; Induced draft blower operating

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 50 / PDF page 50 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  10. EE9
    What the manufacturer documents

    High stage pressure switch circuit is not closed

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate on high stage; furnace operates normally on low stage; Induced draft blower operating

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 50 / PDF page 50 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  11. EEA
    What the manufacturer documents

    Polarity of 115 volt AC is reversed; Poor unit ground

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 50 / PDF page 50 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  12. EEb
    What the manufacturer documents

    Gas valve is not energized when it should be; External Gas Valve Error

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 50 / PDF page 50 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  13. EEC
    What the manufacturer documents

    Gas valve is energized when it should not be; Internal gas valve error

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 50 / PDF page 50 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  14. Eb0
    What the manufacturer documents

    Circulator blower motor is not running when it should be running

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 46 / PDF page 46 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  15. Eb1
    What the manufacturer documents

    Integrated control module has lost communications with circulator blower motor

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 46 / PDF page 46 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  16. Eb2
    What the manufacturer documents

    Circulator blower motor horse power in shared data set does not match circulator blower motor horse power.

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 46 / PDF page 46 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  17. Eb3
    What the manufacturer documents

    Circulator blower motor is operating in a power, temperature, or speed limiting condition

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace operates at reduced performance; Airflow delivered is less than expected

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 46 / PDF page 46 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  18. Eb4
    What the manufacturer documents

    Circulator blower motor senses a loss of rotor control; Circulator blower motor senses high current

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 46 / PDF page 46 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  19. Eb5
    What the manufacturer documents

    Circulator blower motor fails to start 10 consecutive times

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 46 / PDF page 46 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  20. Eb6
    What the manufacturer documents

    Circulator blower motor shuts down for over or under voltage condition. Circulator blower motor shuts down due to over temperature condition on power module

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 46 / PDF page 46 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  21. Eb7
    What the manufacturer documents

    Circulator blower motor lacks information to operate properly; Motor fails to start 40 consecutive times

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 46 / PDF page 46 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  22. Eb9
    What the manufacturer documents

    Airflow is lower than demanded

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace operates at reduced performance or operates on low stage when high stage is expected

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 47 / PDF page 47 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  23. E11
    What the manufacturer documents

    Open roll out switch

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Furnace fails to operate

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 47 / PDF page 47 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  24. E15
    What the manufacturer documents

    Return Air Temperature Sensor Circuit is Open (External)

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: External return air temperature reading not visible on CoolCloud app

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 47 / PDF page 47 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  25. E16
    What the manufacturer documents

    Return Air Temperature Sensor Circuit is Shorted (External)

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: External return air temperature reading not visible on CoolCloud app

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 47 / PDF page 47 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  26. E17
    What the manufacturer documents

    Supply Air Temperature Sensor Circuit is Open (External)

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Supply air temperature reading not visible on CoolCloud app

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 48 / PDF page 48 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  27. E18
    What the manufacturer documents

    Supply Air Temperature Sensor Circuit is Shorted (External)

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Supply air temperature reading not visible on CoolCloud app

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 48 / PDF page 48 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  28. E19
    What the manufacturer documents

    Onboard return air temperature sensor is unplugged

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Onboard return air temperature reading not visible on CoolCloud app

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 48 / PDF page 48 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  29. E1A
    What the manufacturer documents

    Onboard return air temperature sensor is shorted

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Onboard return air temperature reading not visible on CoolCloud app

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 48 / PDF page 48 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

  30. Ed1
    What the manufacturer documents

    Invalid memory card data

    Source wording, not a diagnosis or a confirmed cause. Equipment applicability remains unconfirmed.

    Source context: Operation different than expected or no operation

    Control applicability: IOG-2015F cover families *CVC96*BB / *MVC96*BB only. Alphanumeric LED Status column; exact installed model/control revision and applicability remain unconfirmed.

    Alphanumeric code; no flash cadence, count or period inferred. Exact control identifier: not established.

    Manufacturer-sourced · Not independently verified · Not reviewed by a qualified technicianIOG-2015F · Cover 10/2020 · Printed page 48 / PDF page 48 · Troubleshooting Chart: LED Status and Fault Description

    Furnace not heating? Record observations →What to record and when to seek help → Return to homeowner lookup →

No homeowner checks or professional procedures are supplied. Guidance has not been assessed; this does not mean no service or escalation is needed. This preview is not authorization to diagnose or repair equipment.

These documents describe different model families and control schemes. A later cover date does not establish that one replaces the other. Document availability does not establish currency. No independent review or verified diagnosis is claimed.

How we handle sources and verification →