HVAC REFERENCE · Manufacturer-sourced; not reviewed by a qualified technician
HVACFaultFinder

SYMPTOM GUIDE · NO CODE NEEDED

Furnace starts then shuts off: record where heating stops

The phrase starts then shuts off can mean several things: a startup sound stops before warmth arrives, heat begins briefly, or the room fan keeps running after heat ends. Record the difference you already noticed. It does not establish a failed flame sensor or any other part.

Not reviewed by a qualified technician. This source-based guide provides general information and observations, not an equipment diagnosis.

For a residential gas-furnace heating attempt. This page focuses on where one attempted sequence stopped. Use the short-cycling guide for a repeated pattern over time; neither guide assigns a normal cycle length to every furnace.

Homeowner-safe observations and basic checks

Only use ordinary controls and safe, accessible areas. Skip any check that is unfamiliar or requires equipment access. Not sure is useful information for your service provider.

  1. Describe what started

    Write sound only, airflow, warmth, or not sure. Do not call a sound burner ignition unless you already know that is what you observed.

    Carrier — Furnace Flame Sensor →

  2. Note the last stage you noticed

    Record whether warmth reached the rooms and whether airflow continued after it faded. Do not open the furnace to follow its sequence.

    Carrier — Furnace Flame Sensor →

  3. Record an approximate interval if already known

    An estimate is enough. Do not repeatedly start the furnace, increase the setpoint or clear a lockout to time the event.

    Carrier — Furnace Flame Sensor →

  4. Keep the thermostat reading with the event

    Record room temperature, setpoint and any visible alert. Note a schedule change you already recognize, without entering installer menus.

    Carrier — Furnace Flame Sensor →

Possible explanations—not confirmed causes

More than one condition can produce the same symptom. This list is not ranked by probability and is not a parts-shopping list.

Combustion is not sustained

Carrier identifies flame-sensing trouble as one possible reason ignition does not continue. Similar observations can require assessment of the complete ignition system.

Carrier — Furnace Flame Sensor →

The circulating fan continues after heating

Fan operation can outlast heat production. Air movement alone does not tell you that burners remain on or establish a fault.

Trane — Furnace Blower Not Working →

Decide when to stop and get help

This is an escalation guide, not an automated diagnosis. Choose the situation you already recognize; do not perform a test to fill in a missing answer.

Gas/CO concern, smoke, sparking or wet electrical equipment
For a CO alarm, suspected gas/CO exposure or immediate fire danger, leave for a safe location and contact emergency services or your utility. Keep clear of wet electrical equipment. Do not operate switches, investigate or delay urgent help to complete notes. Source: CPSC — Carbon Monoxide Fact Sheet → Source: Carrier — Furnace Not Turning On →
The symptom persists or returns
Arrange qualified service. Describe only what you already noticed and preserve existing messages; do not repeatedly reset, force operation or reproduce the problem. Source: Carrier — Furnace Flame Sensor →
Only an ordinary setting was accidental
Use the normal owner instructions if safe to correct that setting. If the symptom returns or anything remains uncertain, stop checks and arrange service; temporary improvement does not establish a cause. Source: Carrier — Furnace Flame Sensor →

Professional-only work

Ignition-sequence observation inside the cabinet, flame-current tests, gas/combustion checks and safety-limit diagnosis belong to a qualified professional. Do not reset lockouts repeatedly, open panels or bypass interlocks to watch a cycle.

If you are unsure whether a check is safe, stop and ask a qualified HVAC professional. This general reference has not been reviewed by a qualified technician.

Make notes for a service visit

No code, model or personal details are required. Describe only what you already notice. This tool organizes your answers; it does not interpret them or choose a cause.

  • What started: sound, airflow, warmth or not sure
  • Approximate time before the change, if already known
  • Whether airflow continued after warmth ended
  • Room temperature and setpoint when it happened

Keep names, addresses, passwords and contact details out of these fields. Nothing is uploaded, tracked or automatically saved. Leaving or reloading the page can discard your notes. Copy and download need JavaScript; the guide and prompts do not.

Frequently asked questions

Does a brief start prove a dirty flame sensor?

No. Flame sensing is one possibility; the observation cannot identify the component or justify cleaning it.

Carrier — Furnace Flame Sensor →

Why is the fan still running?

The fan and heat production are not identical stages. Record airflow separately from warmth and let a technician assess an unusual continuing pattern.

Trane — Furnace Blower Not Working →

How is this different from short cycling?

This page organizes one interrupted attempt. Short cycling describes recurring brief cycles; use that guide if you already notice repeated starts and stops.

Carrier — Understanding Furnace Short Cycling →

Sources and limits

Sources reviewed November 17, 2026. These are paraphrased homeowner references with a deliberately narrower safety boundary than some source pages. No source author or manufacturer has reviewed this guide. No guaranteed fix, cost or success rate is claimed.

  1. Carrier — Furnace Flame Sensor ↗

    Flame-proving context and interrupted ignition; no cleaning, sanding, removal, electrical tests or universal part matching adopted.

  2. Carrier — Understanding Furnace Short Cycling ↗

    Repeated interrupted heating, airflow and thermostat context. No universal minute threshold, cause ranking or thermostat relocation instructions adopted.

  3. Trane — Furnace Blower Not Working ↗

    Circulating fan, thermostat fan setting and airflow context. Excludes door removal, fuse/breaker resets, wiring and power-cycle lockout instructions.

  4. CPSC — Carbon Monoxide Fact Sheet ↗

    CO exposure and emergency response; not a component diagnosis.

  5. Carrier — Furnace Not Turning On ↗

    General gas-furnace sequence, safe thermostat observations and when to contact a technician; not an inducer diagnostic test.